Response SL5 Instrukcja Obsługi

14567ENTERESCPOWER ALARMSTATUSALARM MEM/MESSAGELINESTATUS!92 38?036 ZoneWireless Security SystemSL5Installation & Operating Manual

10CONFIGURING THE REMOTE CONTROL1. Remove the rear cover by undoing the smallscrew on the rear of the Remote Control andkeeping it safe for later.2. I

11Note: It is recommended that the telephoneconnection lead is not extended beyond 10 metresbefore connecting to a telephone master orsecondary outlet

127. Ensure that the Reset Jumper Link (P1) and theExternal Tamper Switch Jumper Link (P51) areset in the OFF position.8. Connect battery leads to bot

13The panel will now listen for a valid signal from anew Remote Control or Keypad.The Panel will remain in Learn Mode for 30s.If a valid signal is not

14PASSIVE INFRA-RED (PIR)MOVEMENT DETECTORSPIR Detectors detect movement in a protected areaby detecting changes in infra-red radiation levelscaused f

INSTALLING AND CONFIGURING THE PIR DETECTORS1. Undo and remove the fixing screw from thebottom edge of the PIR Detector, (keep thescrew safe for later

On initial installation the detector should beconfigured into Walk Test ready for testing,(i.e. Pressing down SW1 for 2 seconds).9. Refit the PIR Dete

TESTING A PIR DETECTOR WITH THECONTROL PANEL1. Ensure that the system is in Test Mode (seepage 13).2.Use the and buttons to scroll thr

Do not fix the Detector onto or very close tometalwork (i.e. radiators, water pipes, etc) as thiscould affect the radio range of the device.On PVC doo

6. Switch SW3 is used to enable/disable theinternal/external wired magnetic contact.Position of SW3 FunctionINT. Internal Contact ONINT./EXT. Internal

FOREWORDAll devices in this wireless Alarm System aredesigned and manufactured to provide long reliableservice. The system is designed for ease ofinst

206. Activate the Tamper Switch on the MAGdetector.If the detector is new and not already linked onany security zone the panel will produce twoshort b

The Siren is encapsulated within a toughpolycarbonate housing that also provides fullprotection against adverse weather conditions.An LED indicator un

225. DIP switch 2 marked “AJ” does not function forthis system and should be ignored.6. DIP switch 3 marked “ALARM SOUND” if OFFwill prevent the siren

15. Now scoll through the menu again until ‘WirefreeSiren Service OFF’ is displayed and press .The Siren will produce a single long beepfollowe

INSTALLATION1.Remove the two screws on the batterycompartment cover on the rear of the DummySiren and remove the cover.2.Insert the 4 batteries ensuri

25(Optional)The Control Panel incorporates a terminal block forconnection of a Hard-wired Siren. The connectionterminal block is located inside the Co

26TESTING THE SYSTEMThe Control Panel has a built in test facility toenable you to test the system at any time. Howeverit is recommended that the syst

27DETECTOR TESTBefore commencing testing please ensure that thereis no movement in any PIR protected area for atleast 3 minutes, all doors/windows pro

28MAG Detector – AlarmMAG Detector – TamperSmoke Detector – AlarmSmoke Detector – TamperALARM TEST – WIRELESS SIREN TESTScroll through the menu until

29SPECTRA LIGHTING TESTSScroll through the menu until ‘Spectra Lighting Test’is displayed on the LCD.Press to activate the linked Spectra ligh

3CONTENTSKIT CONTENTS 4INTRODUCTION AND OVERVIEW 5Multiple Users 5User Access Code 5System Arming 5Entry/Exit Delay 5Zones 6Zone Lockout 6Quick Set 6E

30If no acknowledgment signal is receivedform the Alarm Monitoring Service the panelwill beep and the LCD will display:To stop the test early at the

31FACTORY SETTINGSUSER CODE SETUPMaster User: 1234Users 1-6: Not programmedDuress Code: Not programmedSYSTEM SETUP MENUAlarm Duration: 3 minutesEntry/

32With the system in Standby (i.e. with the displayshowing ‘DISARM READY’).PressNote: To get to Standby Mode simply pressrepeatedly until only the POW

33VOICE DIALLER SETUP MENUPhone NumbersRecord Alarm MessagesReplay Alarm MessagesSPECTRA LIGHTING SETUPSet Light-On PeriodSpectra ModeStop TimeStart T

34System Setup DiagramEnter (10-250s)enter timepress ENTER2.3 Entry/Exit Delay: xxxspress ENTERSend DisarmWaiting 30s... display for 3senter t

35SYSTEM SETUPThe parameters in this menu allow the configuration ofgeneral system parameters, such as Alarm Durationand control of any hardwired or o

36Confirm the new device ID code by sendingthe Disarm signal from the same new RemoteControl or Remote Keypad within 15s asfollows…Press o

37To change the setting press .Enter the required delay period (10 - 240s).Press to save new setting and exit, orPress to exit

38ZONE LOCKOUTPrevents a single zone from triggering an alarm more than 3 times before the system is disarmed.(Zone lockout is effective on all zones

39Send CodeWaiting 30s... display for 3s3.1 ZnnWire Zonepress ENTERNo name Front door Back door Side Door Patio door Dining room Living room Lounge

4KIT CONTENTSThe Alarm System should contain the following devices.1xSolar Siren1xDummy Siren1xControl Panel2xPIR Movement Detectors2xMagnetic Door/Wi

40LEARN DETECTOR CODE(zones 1-32 only).Allows a wireless detectors ID code to be learnt andlinked to the selected wireless zone.Linking a New Detector

41NAMEThis enables a name to be allocated to the zone so itcan be identified by its location.Available for all zones 1- 36. Only available forwireless

42PART-ARM 2This controls whether the zone is active when Part-Arm 2 is armed.Default setting: OFF (all zones)Scroll through the Zone menu until ‘3.6

43Press to save new setting and exit, orPress to exit without saving.VOICE DIALLERThe parameters in this menu allow the setting ofthe

44Voice Dialler Setup DiagramWhile recording theLCD should show...5.2.3 Fire Alarm Messagepress ENTERPlaying5.3.2 Intruder Alarm Messagepress ENTERS

45LATCH KEY SETUPThe parameters in this menu configures whichusers the Latch Key feature operates with and thetelephone numbers that the system dials

46After configuring required users press to returnto the top level Latch Key menu.User StatusScroll through the system menu until ‘User xStatu

47FRIEDLAND SPECTRA PLUS LIGHTING SETUPScroll through the menu until ‘7. SPECTRALIGHTING SETUP’ is displayed on the LCD andpress .After configu

48When leaving the premises, the system must be Armed.However, before doing so, check that all windows areclosed and locked, all protected doors are c

49Note: If the system is Disarmed with the RemoteControl the Siren will beep twice, (unless the warningbeeps have been disabled on the Siren).DISARMIN

5MULTIPLE USERSThe system allows for up to 6 Users, a Master anda Duress User to be configured. This allows thesystem Event Log to maintain a record o

50LATCH KEYIf the Latch Key function is enabled and the system is disarmed by a user that is enabled forLatch Key then…1. The first Latch key phone nu

51To stop the LED flashing press or access theEvent Log to read the event message.To read the event log press from Standby.Use

52Double Dial-In for Operation with an ExternalAnswer Phone:If the Remote Access and Control feature is to beused and the system is operating in conju

53VOICE DIALLERIf an alarm is triggered and the Voice dialler isactivated then the first enabled phone number in thedialling sequence will be called a

54The dialler sequence can be stopped early by either…a. All numbers have been dialled three timesb. The system is disarmed c. A call is acknowledged

55PIR Movement Detector:Under low battery conditions the LED behind thedetector lens will flash when movement is detectedto indicate that the battery

56MAINTENANCEYour Alarm System requires very little maintenance.However, a few simple tasks will ensure its continuedreliability and operation.SOLAR S

57123456789101112131415161718192021222324252627282930313233343536EntryDelayALARM RECORDComplete the following information during installation for futu

58NOTESYou may make a note of your System information below.Remote Manager Phone Numbers (Optional)Phone No.1: Phone No. 2:System ID No:Voice Dialler

59Control Unit not working - Power LED OFFor flashing.1. Mains power failure - check if other electricalcircuits are operable.2. Check that mains adap

The Entry-Delay for each zone may be configured forbetween 10 to 250 seconds or disabled completely.Note: To conserve power and maximise battery lifet

60LED on Remote Control not illuminating, oris dim when unit is operated.1. Ensure battery is fitted with correct polarity.2. Ensure battery holder co

61LED on Door/Window Detector illuminatingwhen door or window is opened.1. Low battery - replace batteries.Control Unit Not Contacting RemoteManager S

62The following additional accessories are available to enhance your system and provide further protection anda higher level of security where require

NOTES63

External Solar Siren●RF operating frequency: 868MHz●Sealed lead acid battery 6V/1.2Ahr●Solar Panel 7.5V - Charge Rate typically 60mA●Operation time in

7LATCH KEYWhen the system is Disarmed the Latch Key facility,if enabled, will call the first Latch Key phone numberand replay the user message (record

PLANNING AND EXTENDING YOUR ALARM SYSTEMBefore attempting to install your Alarm System it isimportant to study your security requirements andplan your

9The system may be expanded with additionaldetectors, Remote Controls and Keypads to provideeven greater protection. However, the following rulesshoul