Response SA5 E Instrukcje Operacyjne

Installation & Operating ManualSA56 Zone CommunicatingWirefree Alarm SystemESCENTER2679#*853140

10Any number of Remote Control Units can be used with your system, providing they are all coded with the same system House Code.The Remote Control is

115. The Control Panel must be located within reach of a mains socket.6. If any of the telephone based functions are to be used then the Control Panel

127. Ensure that the “Reset” and the “Hard-Wired Siren tamper detect” jumper links are set in the OFF position.8. Connect battery leads to both back-u

135. Press to save the new setting.6. Press , to return to Standby.TESTING THE CONTROL PANEL & REMOTE CONTROL1. Pres

14When deciding upon the mounting position for the detector the following points should be considered to ensure trouble free operation:1. Do not posit

158. To select the required sensitivity, set DIP switch 5 of SW3 as follows:ON = HIGH sensitivityOFF = LOW sensitivityNote: The recommended setti

16MAGNETIC CONTACT DETECTORSThe Magnetic Contact Set comprises 2 parts; Detector and Magnet. They are designed to be tted to either doors or windows

173. If xing the detector with screws, rst remove the battery holder by carefully tilting up the end and pulling away from the printed circuit board

18Tamper’ will be displayed.12. Open the door/window to remove the Magnet from the Detector.As the Magnet is moved away from the Detector the LED indi

19INSTALLING AND CONFIGURING THE SOLAR SIRENEnsure that the system is in Test mode (see page 13).1. Remove the xing screw from the bottom edge of the

2FOREWORDAll devices in this wirefree Alarm System are designed and manufactured to provide a high standard of security protection and long, reliable

2012. If for any reason you need to disable the Siren, remove jumper link P3 on the circuit board. This will prevent the Siren from sounding during a

21TESTING THE SYSTEMThe Control Panel has a built in test facility to enable you to test the system at any time. However it is recommended that the s

23VOICE DIALLER TEST1. Scroll through the top level Test Mode menu until ‘VOICE DIALER TEST’ is displayed and press .2. If the Voice Dialler

24RESET FACTORY SETTINGS1. Press .This puts the system into Test Mode.2. Undo the Contro

25Telephone Application Setup.If using any of the telephone based functions, (e.g. Answerphone, Voice Dialler, Remote Phone Access & Control etc)

26USERS 1-6Default setting: not programmedScroll through the menu until the required User ‘USER _ SETUP’ is displayed and press .User Access

27The parameters in this menu allow the conguration of general system parameters, such as the Control Panel House Code, Alarm Duration and control of

28Scroll through the menu until ‘2-2-1 Status’ (and the current setting) is displayed.To change the setting press . Press

29REMOTE PHONE ACCESS AND CONTROLIf enabled, this allows the system to be remotely controlled via the telephone.Default setting: OFFScroll through the

3CONTENTSKIT CONTENTS 4INTRODUCTION AND OVERVIEW 5Multiple Users 5System Arming

30ZONE SETUPThe parameters in this menu allow each zones specic function to be congured.Scroll through the programming menu until ‘3. ZONE SETUP’ is

3124 Hour Intruder - used to provide 24 hour monitoring of areas requiring continuous security protection even while the system is Disarmed, (e.g. gun

32PART-ARM 1This controls whether the zone is active when Part-Arm 1 is armed.Default setting: zones 1-4: ON Zones 5-10: OFFScroll through the m

33VOICE DIALLER SETUPThe parameters in this menu allow the setting of the systems Voice Dialler. It allows up to 4 phone numbers to be entered and th

34ALARM MESSAGE PLAY TIMEThis is the total time for which the alarm messages will be played & repeated by the Voice Dialler.Default setting: 70 se

35FULL ARM SETUPThe parameters in this menu control the systems Exit-Delay period and the Entry/Exit Delay warning beeps during Full Arm mode.Scroll t

36PART-ARM 1 SETUPThe parameters in this menu control the systems Exit-Delay period and the Entry/Exit Delay warning beeps during Part-Arm 1 mode.Scro

37PART-ARM 2 SETUPThe parameters in this menu control the systems Exit-Delay period and the Entry/Exit Delay warning beeps during Part-Arm 2 mode.Scro

38TIME & DATE SETUPThe parameters in this menu allow the systems clock and calendar (required for the Event Log) to be congured.Note: The clock w

39SELECTED-USERS SETUPThis congures the individual users that the Latch Key operates with when set to ‘Selected-Users’.Default setting: OFFScroll thr

4KIT CONTENTSThe Alarm System should contain the following devices:1 x Solar Siren1 x Control Panel1 x Remote Control2 x PIR Movement Detectors2 x Mag

40REMOTE MANAGER SETUPThe parameters in this menu congure the system telephone dialler to interface to the Alarm Monitoring Service following the occ

41OPERATING INSTRUCTIONSWhen leaving the premises, the system must be Armed. However, before doing so, check that all windows are closed and locked, a

42If when the system is disarmed the ‘ALARM MEM’ LED is ashing and the panel beeps every 10 seconds, this indicates that an alarm has occurred. To s

43Press to access the Event Log, (from Standby Mode only).The Event Log will automatically display each event in turn starting with the most

45Press to switch the Siren between Service Mode and Operating Mode. LED 5 will illuminate to show that the appropriate signal is being tra

46MAINTENANCEYour Alarm System requires very little maintenance. However, a few simple tasks will ensure its continued reliability and operation.IMPO

47ALARM RECORDComplete the following information during installation for future reference, when adding to your system and to assist trouble shooting.Z

48Control Unit not working – Power LED OFF or ashing.1. Mains power failure - check if other electrical circuits are operable.2. Check that mains a

495. Ensure that detector is mounted the correct way up, (i.e. with detection window at the bottom).6. Ensure that the detector is mounted at the co

5MULTIPLE USERSThe system allows for up to 6 Users and a Master User to be congured. This allows the system Event Log to maintain a record of which

50EXTENDING YOUR ALARM SYSTEMThe following additional accessories are available to enhance your system and provide further protection and a higher lev

51

Novar Electrical Devices and Systems are Quality Assurance Registered to BS EN ISO9001 : 2000, by Asta.Friedland, Novar Electrical Devices and Systems

6FINAL EXIT SET ZONETriggering a detector on a Final Exit zone (e.g. front door) during the Exit-Delay, will cause the delay to reset to 5 seconds wit

7sequence is cancelled/acknowledged by the recipient.For example, the Latch Key facility is useful to inform parents that a child has returned from sc

8Before attempting to install your Alarm System it is important to study your security requirements and plan your installation.PIR Movement Detectors

9Typical Installation using only detectors supplied:1. Place the 1st Magnetic Contact Detector (congured on zone 1) on the front door.2. Place the 1s