Response SA1 E Instrukcje Operacyjne Pobierz pdf (Strona 5)

SYSTEM ARMING

The system has an Instant-Arm and Delay-Arm mode.

If the system is armed in Instant-Arm mode then all

detectors will immediately become fully armed. Any

detector triggered while the system is armed will

immediately sound an alarm.

ENTRY/EXIT DELAY

If the system is armed in Delay-Arm mode this will

activate the system with a xed 15 second entry/exit

delay period. This allows a 15 second period for the

user to exit the property after setting the system with

the Remote Control or at the Keypad. Any detector

triggered while the system is armed will not cause an

alarm condition until after the 15 second entry/exit

delay has expired. This allows time for the system to

be Disarmed before an alarm sounds when re-entering

the property.

Note: To conserve power and maximise battery life

the PIR Detector will only detect movement if there

has been no movement detected within the previous

2 minutes. Consequently the PIR Detector will not

become active until the protected area has been free

from movement for more than 2 minutes.

ALARM LOCKOUT

If a detector is triggered while the system is armed,

the alarm will sound. After the set alarm duration

has ended, the alarm will stop and the system will

automatically reset. Subsequent detectors triggered

will again sound the alarm. If the alarm is triggered

more than 3 times then it will become ‘Locked Out’

and any further alarm signals will be ignored until the

system is re-armed.

TAMPER PROTECTION

All system devices (except the Remote Control)

incorporate Tamper protection features to protect

against unauthorised attempts to interfere with the

device.

Any attempt to remove the battery cover from any

device (except a Remote Control) or to remove the

Siren from the wall will trigger an alarm (unless the

system is in Service Mode), even if the system is

Disarmed.

JAMMING DETECTION

In order to detect any attempts to illegally jam the radio

channel used by your alarm system, a special jamming

detection function is incorporated into the Control Panel

and Siren. If this feature is enabled, an alarm will be

triggered if the radio channel is jammed continuously

for more than 30 seconds or if the system is jammed

for more than 3 periods of 10 seconds in a 5 minute

period. (The Siren will emit a series of rapid beeps for

5 seconds as a pre-alarm warning 10 seconds before a

full alarm occurs).

The jamming detection circuit is designed to

permanently scan for jamming signals. However, it is

possible that it may detect other local radio interference

operating legally or illegally on the same frequency. If

it is planned to operate the jamming detection feature

we recommend that the system is monitored for false

jamming alarms for at least 2 weeks prior to leaving the

jamming detection function permanently enabled.

BATTERY MONITORING

All devices powered by non-rechargeable batteries

incorporate a battery level monitoring feature which

will warn of a low battery status. The batteries on

any device indicating a low battery status should be

replaced immediately.

SYSTEM HOUSE CODE

In order to prevent any unauthorised attempt to

operate or disarm your system, you must congure

your system to accept radio signals only from your

own system devices. This is done by setting a series

of 8 DIP switches in all devices to the same ON/OFF

combination (the House Code) selected by the user/

installer.

The House Code is set up by moving each of the 8 DIP

switches in each device to the same randomly selected

ON/OFF sequence. When setting the DIP switches,

ensure that each switch ‘clicks’ fully into position. Use

the tip of a ballpoint pen or a small screwdriver to move

each switch in turn.

All devices must be congured with the same House

Code in order for the system to operate correctly.

IMPORTANT: It is important that the system House

Code is always changed to a code other than the

factory setting and that all devices are congured

with the same House Code in order for the system

to operate correctly.

INTRODUCTION AND OVERVIEW













1 2 3 4 5 6 7 8 9 10 ... 23 24

Komentarze do niniejszej Instrukcji

Brak uwag

Response SA1 E Instrukcje Operacyjne Strona 5

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Response SA1 E