search

Response SA5 E Instrukcje Operacyjne Strona 10

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
Przeglądanie stron 9
N
ote: If the Panel Tamper alarm sounds during the
installation reset the alarm by pressing:
on the Control Panel Keypad.
Setting the Control Panel
House Code
W
ith the unit in Standby mode (Power LED only
i
lluminated).
1.
Press
to put the system into Programming mode.
‘1. USER SETUP’ will be displayed.
2. Use the and buttons to scroll
through
the menu until ‘2. SYSTEM SETUP’ is displayed.
Press and ‘2-1 Learn House Code’ will be
displayed.
Press again to set the Control Panel to receive
the House code. ‘DIP SW 12345678 & H Code:
xxxxxxxx’ will be displayed.
3.
With the required House Code already configured
on the Remote Control, press the button
on the Remote Control.
When the Control Panel receives the signal from
the Remote Control the Display will change to
show the received house code on lower line of
the display beneath the corresponding DIP switch
numbers (1-8).
4.
Press
to return to Standby mode.
Testing the Control Panel and
Remote Control
1.
Press
to put the system into Test mode.
‘TEST MODE – WALK TEST’ will be displayed.
2.
Press to activate Walk Test.
‘Walk Test Waiting…’ will be displayed.
3.
Press the ‘ARM’ button on the Remote Control.
As the key is pressed the Control Panel will beep
and the type of the device and button will be
shown on the display.
P
ress the other buttons on the Remote Control in
turn, as each button is pressed the Control Panel
will beep and show the button being pressed on
the display.
4.
Test the range of the Remote Control by pressing
t
he ‘DISARM’ button on the Remote Control from
in and around the property and from all locations
where you plan to install detectors. Check that
the Control Panel acknowledges the signal from
the Remote Control each time the ‘DISARM’
button is pressed.
5.
Press to return to the top level menu of
TEST MODE.
Remote Control Unit
The Remote Control Unit is used to Arm, Part-Arm and
Disarm the system.
The Remote Control Unit also incorporates a Panic
switch. Activating the Panic switch on the side of the
Remote Control will immediately initiate a Full Alarm
condition whether the system is Armed or Disarmed.
The alarm can be cancelled by pressing the ‘DISARM’
button on the Remote Control or via the Control Panel.
Any number of Remote Control Units can be used with
your system, providing they are all coded with the
same system House Code.
The Remote Control uses a CR2032 type Lithium cell
which under normal conditions will have a typical life
in excess of 1 year. Under normal battery conditions
the LED on the Remote control will illuminate only
when a button is pressed. However, under low-
battery conditions this LED will flash every time the
button is pressed. When this occurs the battery
should be replaced as soon as possible.
10
,
,
1
2
3
4
Slide up
to operate
Transmit LED
Personal
Attack
Disarm
Arm
Part-Arm
,,
ESC ESC
ESC
Przeglądanie stron 9
1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 43 44

Komentarze do niniejszej Instrukcji

Brak uwag
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Response SA5 E
Systemy kontroli dostępu bezpieczeństwa Response SL2 Instrukcje Operacyjne   (28 strony)
Systemy kontroli dostępu bezpieczeństwa Response SL5 Instrukcje Operacyjne   (52 strony)
Systemy kontroli dostępu bezpieczeństwa Response SA2 E Instrukcje Operacyjne   (24 strony)
Systemy kontroli dostępu bezpieczeństwa Response CWK6 Instrukcje Operacyjne   (48 strony)
Systemy kontroli dostępu bezpieczeństwa Response RE3000S Instrukcje Operacyjne   (34 strony)
  • Vestil Polar Body flex Merik AgaMatrix
  • Giant Akcesoria rowerowe Miele Lodówko-zamrażarki Philips Dyktafony Samsung Akcesoria do paneli płaskich Samsung Notatniki
  • Prochem Apex GTX Cybex SOLUTION X Samsung B2230H BoConcept Carmo Panasonic SDRH40
  • Cooler Master NSE-200-KKN1 Arkusz Danych Behringer B612D Instrukcja Użytkownika Ge JGBS60GEFSA Instrukcja Użytkownika DeWalt DCD936 Instrukcja Obsługi Soehnle Siena Instrukcja Obsługi